wtb: is300/altezza spindle, driver front

[Space Case 0]

fuckin ebay dicks want like 200$ for a 50$ part.

 

 

Need a front is300 spindles. Dont need hub/dust shield etc, just the spindle.

[Gordo 0]

And what is the back story ?

[Space Case 0]

Nothing sweet like curb hopping.

 

 

Making drop spindles, because smashing UCA into my strut tower all the time sucks dick.

[Gordo 0]

Want to see the drop spindle project !

[Gordo 0]

The early spindle was used on all these cars:

Japan 10/1998-06/2005 TOYOTA ALTEZZA, ALTEZZA GITA GXE1*,JCE1*,SXE10 N. America 05/2000-06/2005 LEXUS IS300 JCE10

Japan 10/1992-08/1996 TOYOTA MARK 2 GX90,LX90,SX90,JZX9*

Japan 09/1996-09/2000 TOYOTA MARK 2 GX10*,JZX10*,LX100

Japan 10/2000-05/2007 TOYOTA MARK 2, MARK 2 BLIT GX11*,JZX11*

Japan 10/1992-08/1996 TOYOTA CHASER GX90,JZX9*,LX90,SX90

Japan 09/1996-05/2001 TOYOTA CHASER GX10*,JZX10*,LX100,SX100

Japan 10/1992-08/1996 TOYOTA CRESTA GX90,JZX9*,LX90,SX90

Japan 09/1996-05/2001 TOYOTA CRESTA GX10*,JZX10*,LX100

Japan 05/1998-05/2007 TOYOTA PROGRES JCG1*

Japan 08/2000-03/2001 TOYOTA ORIGIN JCG17

Japan 08/1995-07/2001 TOYOTA CROWN, CROWN MAJESTA GS151,JZS15*,LS151,UZS15*

Japan 09/1999-05/2007 TOYOTA CROWN, CROWN MAJESTA GS171,JKS175,JZS17*,UZS17*

[Space Case 0]

Indeed.

[Gordo 0]

I want a JCG17 Origin, damn it.......

 

[Rue 0]

I know someone... I'll hit him up in the AM

[Austin 0]

Drop spindles are allright, but make sure you run an rca or the geometry gets all fucked. I just pocketed the strut towers and its been great.

[Space Case 0]

Well its not a drop spindle without adding an RCA. Without doing both, you just fuck up your geometry to gain space.

 

 

But ya, I have some 30MM RCAs and made an adjustable jig for height. Will post photos once complete. Itll be sick.

[NAC 0]

Saw this mkii IRL the other day. Fully legit. These things look so good in person. Full faith in this turning out legit.

[Space Case 0]

any headway?

[Gordo 0]

I can get you some out of Japan.....

[Space Case 0]

Yah, so can I..

[RINTHAL 0]

hey I might have one...

[Space Case 0]

Bump

Always looking for cores. Have already made and sent out 4 sets, and have a set on my own car of course. Can post a separate add if PPL are interested?

[Gordo 0]

Where are the promised photos ?????????

[Space Case 0]

[Gordo 0]

Nice !

[Space Case 0]

Thanks! I already have 4 sets out, all of them with great reviews. Running RCAs with short spindles makes a huge difference.

 

I'm running 30MM KTS RCAs on my JZX110, and 30MM of spindle correction, but my jig is adjustable to cut however little or much is needed depending on your ride height, RCA size, wheel size, etc.

[Gordo 0]

I'm trying to grow balls big enough to try doing that to my Datsun truck.

But it's a king pin set up, and would require cuts above, and below the king pin & spindle area.