-
Content Count
1775 -
Joined
-
Last visited
Content Type
Profiles
Forums
Calendar
Everything posted by Foompla
-
what ever happened to this car?
Foompla replied to Foompla's topic in Cressida Mark II Chaser Cresta Verossa IS Altezza
Miss you too. -
what ever happened to this car?
Foompla posted a topic in Cressida Mark II Chaser Cresta Verossa IS Altezza
-
I vote for a fuel issue. Long crank indicative of bleed down.
-
Gordo might be the only person to ever wear out a 14mm hex drive.
-
Lexus is300 Limp mode
Foompla replied to Gibbs's topic in Cressida Mark II Chaser Cresta Verossa IS Altezza
If it's not throwing a code I don't think it's in limp mode. Start checking the basics -
I could set a clock by my temp gauge. They're rock solid ironically. Throw a resistor on the harness end of the engine to validate. My money is on the sender.
-
give him props. he actually set up the cel. check for vacuum leaks again. these things arent that smart.
-
Toyota X Chassis Workshop Manual and Wiring Guide Motherload
Foompla replied to brian's topic in Cressida Mark II Chaser Cresta Verossa IS Altezza
1. You'd need someone from Toyota in Japan to send you a cease and desist. 2. They don't give a shit. -
Looks good. Thought youd stay with the auto. Did you get bored?
-
OK, upon review, that's a code for the o2 sensor, and I am completely talking out of my ass. sending you over the RM stuff.
-
What are the codes? That reference circuit is shared by a couple of sensors, but I think the temp sensor grounds in the block. The ecu shouldn't care about temp when the vehicle is in closed loop, if it's ever getting there. It looks like you are getting the correct voltage to the senor. I am curious why the one connector says 2.8 ohms. That might be going back to another wire this is a source of your issues. I need to check a diagram. I would unplug the cold start injector, and see if it makes a difference. I can look at the RM for you if you want. just PM me your number so I can text it to you.
-
Ill take the shell off your hands if you still got it.
-
I have no idea what direction I want to go in. Help me pick a swap
Foompla posted a topic in X3,X6,X7,X8
I'll probably end up picking it up in May, depending on what's available in Dallas area at the time. -
I put 60k miles on my first 7m with rods knocking on start. Pretty sure they're just supposed to do that.
-
Im in socal now, will be in Texas in about a month. LMK
-
My problem is that I refuse to pay more than $500.00 for a car. I was still interested in buying some shit, but I think he took a long walk off a short ledge.
-
I have no idea what direction I want to go in. Help me pick a swap
Foompla replied to Foompla's topic in X3,X6,X7,X8
Thats the only reason I was tracking it, but I didn't catch what it went up to and they don't show it after the fact. -
I have no idea what direction I want to go in. Help me pick a swap
Foompla replied to Foompla's topic in X3,X6,X7,X8
I was tracking this one. https://www.copart.com/lot/29613426/ -
I think kyle has dual accounts
-
you took too long, ordered coils. I'm ok with Chinese wheels. 18s or less.
-
Your mother is heartbroken.
-
I have no idea what direction I want to go in. Help me pick a swap
Foompla replied to Foompla's topic in X3,X6,X7,X8
Take that shit the fuck outta of my thread you cockhoarding neophyte -
I'm going to be in Plano / Grayson County. 60ish miles north of Dallas. Post pics.