Jump to content


The ultimate X-chassis clutch master cylinder data base

  • Please log in to reply
26 replies to this topic

Poll: Where I came up with my info (15 member(s) have cast votes)

I got my master cylinder info from:

  1. Direct measurement (5 votes [33.33%])

    Percentage of vote: 33.33%

  2. Read it on TC.net (0 votes [0.00%])

    Percentage of vote: 0.00%

  3. Read it on Zilvia (1 votes [6.67%])

    Percentage of vote: 6.67%

  4. Heard it from a buddy who knows a forum master on Honda-Tech (0 votes [0.00%])

    Percentage of vote: 0.00%

  5. Dreamt it after eating bad tacos (8 votes [53.33%])

    Percentage of vote: 53.33%

  6. Don't know, don't care, I run an auto. (1 votes [6.67%])

    Percentage of vote: 6.67%

Vote Guests cannot vote

#21 Mitto


    Aus-fail-ian Pride

  • real members
  • 725 posts
  • Gender:Male
  • Location:L-Res
  • Interests:Interesting things that interest me and others around me who are also interested in the things that interest me...

  • Country:Australia

Posted 15 June 2013 - 06:28 PM

Then why the fuck did you post for cunt?!


This thread is here for useful information not for some faggot who's too fucking lazy to do the work himself to post bogus shit...


Fuck right off with your wasteful fucking failed existence unless you have helpful info...

#22 Me86Rob


    I HATE 7M

  • real members
  • 87 posts
  • Gender:Male
  • Location:Georgia
  • Country:United States

Posted 16 June 2013 - 07:42 AM

I buy a factory 5 speed Cressida, and I'm "too lazy to do it myself'. Priceless. Also, you can walk into any parts store and get an x3/x6/x7 Clutch master, usually within 24 hrs. As far as an x8 goes seems like ya'll have it pretty much covered. If you need anything checked dimentionally just let me know and I can pull one off the shelf at work and get you any measurements you need. 


#23 Gordo


    Resident Grumpy Old Man

  • real members
  • 7444 posts
  • Gender:Male
  • Location:The Republic of Texas
  • Interests:Your mother
  • Country:Texas

Posted 16 June 2013 - 08:16 AM

OK, I need to know the taper, in degrees of both the X8 tie rod ends, and the ball joints.

Get me that, and I will be impressed.

Prefixes for 'Gordo'
 口 Holy Shit  
口That ass hole,  
口The Magnificant  
口That old fart,  
口The infamous  
口That crazy  
口That 7M guy,   
Best JZXP statement:
Jacob - "We're all fucked. We'll be comparing everything to a Japanese taxi for the rest of our lives."


#24 Panda



  • real members
  • 37 posts
  • Gender:Male
  • Location:Flerduh
  • Country:Azerbaijan

Posted 16 June 2013 - 10:09 AM

I'm sure this has probably been covered but what the hell;

On my x72 I used a MKIII Supra master and clutch pedal. Re-drilled one hole in the firewall for the master and one on the pedal assembly for the upper mounting point. Easy peasy.

#25 Demesio



  • real members
  • 1458 posts
  • Gender:Male
  • Location:CA
  • Country:China

Posted 14 March 2018 - 06:35 AM

Any of you losers drive your car enough to kill the clutch master?


I have the celica and MKII combo, it seems like I have to replace it every two years... it seems like the pedal pushes the pin at an angle and the piston just eats shit eventually.

#26 battleaxe



  • real members
  • 922 posts
  • Gender:Female
  • Location:On an Island in the Pacific
  • Country:Canada

Posted 14 March 2018 - 07:14 AM

I have that combo in my x8. I modded the pedal so I have more travel because it wasn't engaging and disengaging the clutch very good. It has a lot of play where the shank and pin go. I dont remember it doing anything abnormal...but I have very little mileage on mine

#27 ChriSOL



  • Moderator
  • 7039 posts
  • Gender:Male
  • Location:Tyexxus
  • Country:Afghanistan

Posted 14 March 2018 - 04:24 PM

mkiii pedal, st18x master. angle is shitty causing a slight leak. moving a mounting hole slightly then reinforcing is the answer in the long run, i think.

My friend that lives in US showed me CraigsList while we search for my Cressida. You find lots of odd things on that site. Lots of fat US girls looking for a free ride from black basketball type American man.

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users